Pelleting
: THE MITRED JOINTindicates the method of pelleting and screwing the corner of a picture frame. The mitre joint is first screwed and a pellet of the same timber is made to fill the hole which has been bored to receive the screw head. The pellet is glued in position and levelled off.
Fig. 358.—Patera Covers to Hide Screws. 
More
-
Loose Tongues
There are two methods of jointing with loose tongues, viz., the use of the cross tongue, , and the use of the feather tongue, . Cross tongues are the stronger when glued in their position and can be used very much thinner than feather tongues. Feather... Machine-made Dovetails
As a general rule machine-made drawer and box dovetails show both the pins and the tails of exactly the same size. The reason is obvious after an inspection of , which shows the position in which the pieces are held during the machining operations. ... Making Dowels
Many, however, prefer to make what they require for the work in hand, and the following is the method that is generally employed. Pieces of straight-grained wood are wrought to a square section, after which the corners are planed away to form an oct... Miscellaneous Joints
<p>Weather boards.—For outdoor buildings, such as garages, garden sheds, toolhouses, etc., "weatherboarding" is often preferred to ordinary matchboarding, chiefly because of the facility with which it throws off the rain. The boarding can be b... Mitred And Moulded Joint
shows a type of joint largely used in light cabinet work. The method of mitreing the moulding and tenoning the stile to rail is indicated.</p> ... Mitreing
The term mitreing is generally used to denote the type of joint used at the corner of a picture frame; or where two pieces of wood are bevelled away so as to fit each other, as the skirting or plinth mould at . In these cases the timber is cut so th... Mitreing A Moulded Door Frame
illustrates the method of mitreing the moulded portion of a door frame where the joint is dowelled, not tenoned. A small wooden template is made out of beech or other hardwood, having its ends cut at 45 degrees. This template is placed on the rail,... Mortise And Tenon With Mitred Face
This is a useful method of jointing framing which has square edges as shown; and it is equally useful even if the face edges have moulds worked upon them. If the joint has square edges a rebate may be formed to accommodate a panel by fixing a bolect... Mortising Puzzle
The ordinary mortising exercise is, after the first two or three attempts, generally voted as uninteresting, but, although the simple puzzle shown in is practically an exercise in mortising, yet, forming as it does a puzzle, it becomes a fascinating... Muntin And Skirting Joint
In the case of panelled rooms it is usually necessary to scribe the muntins (or uprights) to the skirting. The method is shown in . The bead moulding of the skirting is only partly removed, as indicated, leaving a solid portion to which the muntin is... Notched Joints
is a "notched joint," where two joists, or scantlings, cross each other, the object of the joint being to prevent the joists moving from their position without materially weakening them. For an end notch, see .</p> <div> <img src="/images/f349.jpg"... Open Joint Hingeing
The next three illustrations apply more particularly to the hanging of the ordinary household door.</p> <p> is termed "open joint hanging," from the fact that when the door is open a certain amount of open space exists between the edge of ... Other Varieties
At we have an everyday method of jointing circular-fronted cabinet door frames. Great care must be taken in setting out and making, or a twisted frame will result.</p> <p>Then at are shown two familiar examples of dovetailing the bearer to the car... Outside Hingeing
illustrates the portion of a door frame and carcase end when the door is hung on the face of the carcase. The correct method of letting in the hinge is shown in the enlarged section , but, as previously mentioned, the hinge may have its entire thic... Patera Covers
In cases where the style of ornament permits of it, patera covers are used instead of pelleting. shows the jointing of shaped spandrails, etc., to carcase ends of light portable cabinet work, etc. A hole is bored about 3⁄8 in. deep into the en... Pelleting
indicates the method of pelleting and screwing the corner of a picture frame. The mitre joint is first screwed and a pellet of the same timber is made to fill the hole which has been bored to receive the screw head. The pellet is glued in position an... Pinning
shows the tenoning of the inside end of a wardrobe to the top of the carcase. This is also called pinning. The tenons should be wedged diagonally. The tenons and the distance between the tenons are more satisfactory if made equidistant, because if ... Planing
After sawing the piece to approximately the correct angle, it is necessary on high-class work to plane the cut end so as to give a perfect finish and enable a glued joint to be made. This may be accomplished by using the plane on the shooting board, ... Ploughing
When grooves have to be worked in the edge or face of a board to receive tongues, the process is generally called ploughing, and it is usually accomplished by a special tool called a plough (or, as it is occasionally spelt, "plow"). When a ... Position Of Hinges
Another difficulty to the beginner is the position for his hinges, and it may here be stated that the general rule is to carry a line across the face of the work from the inside of the cross rail and place the hinge at E, as .</p> <div> <img src="/i... Puzzle Joints
<p>Puzzle Joints are not only interesting in themselves, but are often excellent studies in craftsmanship. The majority of them, if to be satisfactory as puzzles, call for very careful setting out and cutting, entailing the same degree of skill that ... Rafter Joint
shows an everyday joint, as used at the juncture of the principal rafter and the tie-beam in roof truss work. A sketch of piece A is shown separated, and it should be noted that the depth of the cut portion B should not be more than one-fourth of t... Removing Haunching
After removing the mortise hole, the small portion which is called the haunching will require to be removed with a chisel. This calls for no special remark, as it is clearly shown in . shows an everyday type of mortise and tenon joint separated; it ... Rising Butt Hinges
is the rising butt hinge, used on dining and drawing-room doors, so that when the door is opened the door rises sufficiently to clear the thickness of the carpet. This hinge has also an advantage over the ordinary butt hinge in that it is self-closi... Roof Joints
shows the method of tenoning the principal rafter to the king post, whilst illustrates the tenoning of the struts to the king post, and the king post to the tie beam. Both these examples are used in roof work. (See also .)</p> <div> <img src="/imag... Sash Bars
shows how to tenon a moulded sash bar to the rebated cross rail. In this illustration both shoulders of the moulded bar are shown square, but in the best class work these shoulders may be slightly housed into the cross rail to prevent side play. Th... Saw Work
Take a marking awl, or a knitting needle which has had its end sharpened, and mark the lines of the dovetail in a similar manner to that shown at . Remove the piece A, , and the lower piece shown at will clearly show the marks <em>aa</em> as they a... Sawing
Lay the work on the cutting board as at ; or, if you prefer, put the work in the vice. Carefully saw down the work until you <em>just touch</em> the gauge line. Do not press heavily with the saw; use it lightly; the weight of the back iron which is fi... Sawing
The wood should be put in the vice as . Taking up a saw, with the index finger on the side of the handle, commence sawing, and proceed until you come to the position indicated by the dotted hand and saw A; this will leave a saw kerf or cut running di... Sawing Block
For sawing mouldings, etc., to their approximate shape, a home-made sawing block is generally used, as shown at . Two pieces of wood are glued one on the top of the other, the required angle is transferred thereto, and the saw kerf made. In the sket...