Simple Turning Lathe
: WOOD TURNINGA very simple turning lathe may be made by following these instructions:
More
-
Saw Clamps
You may easily make a pair of saw clamps as follows: Take two pieces of hard wood, each three inches wide, seven-eighths of an inch thick, and equal in length to the longest saw. Bevel one edge of each as shown in A (Fig. 15), so as to leave an edg... Scarfing
This method of securing members together is the most rigid, and when properly performed makes the joint the strongest part of the timber. Each member (A, Fig. 212) has a step diagonally cut (B), the two steps being on different planes, so they form ... Sector And Segment
Now examine the shape of the body formed by two of the radial lines (E, E) and that part of the circle which extends from one radial line to the other. The body thus formed is a sector, and it is made by two radiating lines and a curved line. Learn ... Self-supporting Roofs
In putting up, for instance, self-supporting roofs, or ceilings with wide spans, and steeples or towers, the bridge principle of trussed members should be understood. The most simple bridge or trussed form is the well-known A-shaped arch. <div> <im... Setting Door And Window Frames
The next step in order is to set the door and window frames preparatory to applying the weather boarding. It is then ready for the roof, which should be put on before the floor is laid. ... Setting Up
First set up the corner posts, plumbing and bracing them. Cut a top plate for each side you are working on. <div> <img src="/images/fig231.jpg" alt="Fig. 231." title="" height="64" width="400" /> Fig. 231. </div> ... Shading Effects
Now, to examine it properly so as to observe what the draughtsman wishes to express, look at Fig. 138, in which the three diverging lines (A, B, C) are increased in thickness, and the cube appears plainly. On the other hand, in Fig. 139, the thicken... Shading With Beads And Rabbets
You will see from the foregoing, that these embellishments are serviceable because they provide the article with a large number of angles and surfaces to cast lights and shadows; and for this reason the boy should strive to produce the effects which... Shadows From A Solid Body
We can understand this better by examining Fig. 129, which shows a vertical board, and a beam of light (A) passing downwardly beyond the upper margin of the board. Under these conditions the upper margin of the board appears darker to the vision, by... Signs To Indicate Measurements
The small circle (°) is always used to designate <em>degree</em>. Thus 10° means ten degrees. Feet are indicated by the single mark '; and two closely allied marks " are for inches. Thus five feet ten inches should be written 5' 10"... Simple Saw Setter
Take a block of wood, a 4 by 4 inch studding, four inches long. Get a piece of metal one-half inch thick and two inches square. Have a blacksmith or machinist bore a quarter-inch hole through it in the center and countersink the upper side so it m... Simple Turning Lathe
A very simple turning lathe may be made by following these instructions: ... Soft Wood
As, presumably, most of your first work will be done with pine, poplar, or other light-colored material, and, as many people prefer the furniture to be dark in color, you should be prepared to accommodate them. ... Soft Woods
It is also well for the novice to do his initial work with a soft wood, because in joining the parts together inaccuracies may be easily corrected. If, for instance, in mortising and tenoning, the edge of the mortised member is not true, or, rather,... Spirals
There is no more difficult figure to make with a bow or a circle pen than a spiral. In Fig. 150 a horizontal and a vertical line (A, B), respectively, are drawn, and at their intersection a small circle (C) is formed. This now provides for four cent... Staining Contrasting Woods
Then, again, do not stain a piece of furniture so that one part represents a cheap, soft wood, and the other part a dark or costly wood. Imagine, for instance, a cabinet with the stiles, rails and mullions of mahogany, and the panels of pine or popl... Stains As Imitations
It will be well to remember one thing as to stains. Never attempt to stain anything unless that stain is intended to produce an imitation of some real wood. There are stains made up which, when applied, do not imitate any known wood. This is bad t... Steps In Cutting Mortises
Examine Fig. 208, which, for convenience, gives six successive steps in making the mortise. The marks <em>a</em>, <em>b</em> designate the limits, or the length, of the mortise. The chisel (C) is not started at the marking line (A), but at least an ... Straight-faced Moldings
Now let us carry the principle still further, and, instead of using various type of moldings, we will employ nothing but straight strips of wood. This treatment will soon indicate to you that the true mechanic or artisan is he who can take advantage... Technical Designations
As all geometrical lines have designations, I have incorporated such figures as will be most serviceable to the boy, each figure being accompanied by its proper definition. <div> <table summary="Fig 146/147" border="0" cellpadding="0" cellspacing=... The "odd Job" Tool
A most useful special tool, which combines in its make-up a level, plumb try-square, miter-square, bevel, scratch awl, depth gage, marking gage, miter gage, beam compass, and a one-foot rule. To the boy who wishes to economize in the purchase of too... The Angle Of Filing
By angle is meant the cutting position of the file. In Fig. 12, the lines B represent the file disposed at an angle of 12 degrees, not more, for a rip saw. For a cross-cut the angle of the file may be less. ...