Wax Finishing
In wax-finishing hardwoods, use a paste filler and shellac varnish to get a good surface. Of course, the wax may also be rubbed into the unfilled wood but that gives you quite a different effect from the regular wax polish, says a correspondent of Wood Craft. With soft woods you first apply a stain, then apply a liquid filler or shellac, according to the quality of work to be done. The former for the cheaper job. The usual proportion of wax and turpentine is two parts of the former to one part of the latter, melting the wax first, then adding the spirits of turpentine. For reviving or polishing furniture you can add three or four times as much turpentine as wax, all these proportions to be by weight. To produce the desired egg-shell gloss, rub vigorously with a brush of stiff bristles or woolen rag.
More
-
Filling Oak
<p>A very good hardwood filler for oak, either for a natural or golden effect, may be made from two parts of turpentine and one part of raw linseed oil, with a small amount of good japan to dry in the usual time. To this liquid add bolted gilder's whi... Home-made Lawn Swing
<div> <img src="/images/Furniture/i-047.jpg" alt="" width="600" height="373" /> The Completed Swing </div> <p>The coming of spring and summer calls forth various kinds of porch and lawn furniture. A porch or lawn swing to accommodate two or more perso... Home-made Mission Chair
<div> <img src="/images/Furniture/i-004.jpg" alt="" width="372" height="600" /> Suitable for Dining Room Use </div> <div> <img src="/images/Furniture/i-006.jpg" alt="" width="539" height="600" /> Details of Chair Construction </div> <p>A mission chai... How To Bend Wood
<p>The process for making bent wood for furniture parts is the same as for any other kind of bent-wood work. The pieces should be made close to the size, with only enough material left on them for "cleaning up" after the bending has been done. The p... How To Make A Combination Billiard Table And Davenport
<p>A small size billiard table which can be converted quickly into a davenport is made as follows: Secure clear, selected plain sawed white oak in sizes as indicated by the drawing. Have these planed at the mill to the widths and thicknesses specified... How To Make A Dowel-cutting Tool
<p>Secure a piece of steel about 1/4 in. thick, 1-3/4 in. wide and 8 in. long. Drill various sized holes through the steel as shown in Fig. 1, leaving the edge of each hole as sharp as the drill will make them. Cut off a block of wood the length nece... How To Make A Mission Library Table
<p>The mission library table, the drawings for which are here given, has been found well proportioned and of pleasing appearance. It can be made of any of the several furniture woods in common use, such as selected, quarter-sawed white oak which will ... How To Make A Pyrographer's Table
<div> <img src="/images/Furniture/i-074.jpg" alt="" width="600" height="398" /> Convenient Pyrographer's Table</div> <p>Any pyrographer will appreciate the construction of the table and cabinet as illustrated. Anyone doing burnt wood work will know th... How To Make A Settee
<p>This handsome piece of mission furniture is designed to be made up in three different pieces as desired, the only changes necessary being in the length of the one front and the two back rails. The settee can be made into a three-cushion length by a... How To Make A Tabouret
<p>Secure from the planing mill the following pieces and have them planed and sandpapered on two surfaces: For the top, one piece 7/8 in. thick and 17 in. square. For the legs, four pieces 7/8 in. thick, 4-3/4 in. wide and 18-1/2 in. long. For the lo... How To Make Black Wax
<p>When putting a wax finish on oak or any open-grained wood, the wax will often show white streaks in the pores of the wood. These streaks cannot be removed by rubbing or brushing. Prepared black wax can be purchased, but if you do not have any on ha... Magazine Rack
<p>The accompanying cut shows a magazine rack that will find favor with many amateur wood-workers on account of its simplicity in design and its rich, massive appearance when properly finished. It is so constructed that each piece may be polished, st... Magazine Stand
<div> <img src="/images/Furniture3/i-103.jpg" alt="Stand Complete" title="" width="298" height="600"> Stand Complete </div> <p>If you do not possess the necessary tools for getting out the material used in this piece of furniture, it can be purchased... Mission Stains
<p>What is mission oak stain? There are many on the market, with hardly two alike in tone. The true mission oak stain may be said to show a dull gray, the flakes showing a reddish tint, while the grain of the wood will be almost a dead black. To produ... Music Rack And Bookstand
<p>The illustration shows a very handy music and bookstand, which also can be used at the bedside as a reading stand. The following list of material will be required for construction:</p> <ul> <li>1 standard, 1-1/8 by 1-1/8 by 37 in., S-4-S.</li> ... Oak Stain
<p>An easy and at the same time a good way to stain oak in imitation of the fumed effect, is to boil catechu in the proportion of 1/4 lb. to 6 lb. of water, after which cool and strain. Apply this to the wood, and when dry treat with a solution of bi... Quarter-sawed Oak Settee
<p>The mission settee shown in the accompanying picture should be made of quarter-sawed white oak. The material needed will be as follows:</p> <ul> <li>4 posts, 3-1/4 by 3-1/4 by 36-1/2 in., S-4-S.</li> <li>4 end rails, 1-1/2 by 5 by 32 in., S-4... The Fuming Of Oak
<p>Darkened oak always has a better appearance when fumed with ammonia. This process is rather a difficult one, as it requires an airtight case, but the description herewith given may be entered into with as large a case as the builder cares to constr... Tool For Marking Dowel Holes
<p>On some work it is quite difficult to locate the exact point for a dowel, but with the tool illustrated placed between the joint to be made and the parts gently pressed together you have the exact point for the dowel in each piece. The tool is mad... Wax Finishing
<p>In wax-finishing hardwoods, use a paste filler and shellac varnish to get a good surface. Of course, the wax may also be rubbed into the unfilled wood but that gives you quite a different effect from the regular wax polish, says a correspondent of ...