Toggle navigation
Wood Workings.ca
Home
Woodworkings
Carpentry
Wood Turning
Handwork
Furniture Making
All Carpentry Page 18
The Flooring Joist
The flooring joists (A) are then put down (Fig. 230). These should extend clear across the house from side to side, if possible, or, if the plan is too wide, they should be lapped at the middle wall and spiked together. The ends should extend out ...
The Foundation
This may be of brick, stone or concrete, and its dimensions should be at least 1½ inches further out than the sill. ...
The Frame Assembled
The frame is now ready to assemble, but before doing so a drawer opening and supports should be made. The ends of the supports may be mortised into the side pieces or secured by means of gains. Mortises and tenons are better. ...
The Gage
The illustration (Fig. 19) shows one of the most useful tools in the kit. It is used to scribe the thickness of the material which is to be dressed down, or for imprinting the edges of tenons and mortises. Two should be provided in every kit, for co...
The Gage
A man, who professed to be a carpenter, once told me that he never used a gage because he could not make it run straight. A few moments' practice convinced him that he never knew how to hold it. The illustration shows how properly to hold it, and th...
The Grindstone
As most of the tools require a grindstone for sharpening purposes, an illustration is given as a guide, with a diagram to show the proper grinding angle. In Fig. 16 the upright (A) of the frame serves as a line for the eye, so that if the point of...
The Grindstones
It is better to get a first-class stone, which may be small and rigged up with a foot treadle. A soft, fine-grained stone is most serviceable, and it should have a water tray, and never be used excepting with plenty of water. An Oil Stone is as esse...
The Gutter
In Fig. 233 I show a most serviceable way to provide for the gutter. A V-shaped notch is cut out of the upper side of the rafter, in which is placed the floor and a side. This floor piece is raised at one end to provide an incline for the water. ...
The Hard-ribbed Grain In Wood
This peculiarity of the grain in ash makes it a beautiful wood when finished. Of the light-colored woods, oak only excels it, because in this latter wood each year's growth shows a wider band, and the interstices between the ribs have stronger contr...
The Hatchet
The hatchet should be ground with a bevel on each side, and not on one side only, as is customary with a plasterer's lathing hatchet, because the blade of the hatchet is used for trimming off the edges of boards. Unless ground off with a bevel on bo...
The House And Embellishments
The refined arts, such as sculpture and painting, merely embellish the home or the castle, so that when we build the structure it should be made with an eye not only to comfort and convenience, but fitting in an artistic and æsthetic sense. It...
The Jack Plane
This plane has the cutting edge of its blade ground so it is slightly curved (Fig. 6), because, as the bit must be driven out so it will take a deep bite into the rough surface of the wood, the curved cutting edge prevents the corner edges of the bi...
The Legs
Now prepare two legs (D) for the tail end of the frame, each 32 inches long, with a chamfer (5) at one end, and provided with four bolt holes. At the lower end bore a bolt hole for the cross base piece. This piece (E) is 4" × 4", 21 ...
The Length Of The Mortises
Then take a small try square (Fig. 28) and add two cross lines (B, C) on each of the inner surfaces, the second line (B) one-half inch from the finish line (A), and the other line (C) seven inches down from the line (A). The side facing boards, here...
The Mandrel
A piece of steel tubing (S), No. 10 gage, ¾ inch in diameter, 11½ inches long, will be required for the mandrel. Get a blacksmith, if a machine shop is not convenient, to put a fixed center (1) in one end, and a removable centering mem...
« Previous
Next »
Showing
256
to
270
of
313
results
1
2
...
12
13
14
15
16
17
18
19
20
21
Most Viewed
Roofing Trusses
The Roman-doric Column
Saddle Joint
Proportional Dividers
The Warren Girder
Soft Woods
The Hatchet
Saw Clamps
Least Viewed
The "odd Job" Tool
Great Contrasts Bad
Where Mortises Should Be Used
Front And Side Lines
Hard Wood Imitations
Polishing Stained Surfaces
The Carpenter And Architech
Forcing Saws In Wood